Journals →  Chernye Metally →  2023 →  #9 →  Back

10th anniversary of the department of Design Engineering and Operation of Metallurgical Machines and Equipment of Nosov Magnitogorsk State Technical University
ArticleName Refinement of methodology for analytical assessment of contact interaction of elements of rolls - strip systems in four-roll stands
DOI 10.17580/chm.2023.09.14
ArticleAuthor A. V. Antsupov (Jr.), A. V. Antsupov, V. P. Antsupov, E. S. Ryskina

Nosov Magnitogorsk State Technical University, Magnitogorsk, Russia:

A. V. Antsupov (Jr.), Cand. Eng., Associate Prof., Dept. of Design and Operation of Metallurgical Machines and Equipment, e-mail:
V. P. Antsupov, Dr. Eng., Prof., Dept. of Design and Operation of Metallurgical Machines and Equipment
E. S. Ryskina, Cand. Eng., Associate Prof., Dept. of Design and Operation of Metallurgical Machines and Equipment


Bauman Moscow State Technical University, Moscow, Russia:

A. V. Antsupov, Dr. Eng., Associate Prof., Dept. of Mechanical Engineering Technologies


Stricter requirements for reducing the thickness of hot-rolled and cold-rolled wide strips have required the refinement of classical models to describe the process of their contact interaction with working rolls in the four-high mill stands. Therefore, modern models are forced to use an elastic-plastic scheme of the deformation zone, in which, along with the plastic resistance to deformation of the strip, its resistance is taken into account in the areas of elastic compression at the inlet and elastic recovery at the outlet of the rolls. However, to calculate the coefficient of friction in the new zones of elastic lag and advance, methods for determining it in a plastic deformation zone are still used. To eliminate this contradiction and correctly describe the physical nature of the elastic frictional interaction of rolls and strips, the article suggests using the N. M. Mikhin friction model of deformable solids. The adaptation of the model to the friction conditions of the rolls with the strip on elastic sections allowed us to identify the dependence of the relationship of the coefficient of friction with external pressure, the parameters of the roughness of the rolls, the physical properties of the strip material and the tribotechnical characteristics of the contact. Based on the analysis of this dependence, a linear law of increasing the coefficient of friction from the input plane and the output plane towards the plastic section, and its value varies from the reference value of the pressure-viscosity coefficient to the value of the coefficient of friction on the plastic section. The established pattern of friction was taken into account when constructing a method for calculating the roll force, which was used in the development of routes for moving rolls along the stands of PJSC "Magnitogorsk Iron and Steel Works" mill 2000 in accordance with the degree of their loading, and the most effective of them were introduced into commercial operation.

keywords Contact interaction, parameters of the interaction, roll force, elastic-plastic model, deformation zone, coefficient of friction, calculation method, patterns of friction, elastic zones

1. Kozhevnikov A. V., Skripalenko M. M., Kozhevnikova I. A. et al. Estimation of deformation zone parameters during symmetric and asymmetric strip rolling using computer modeling. Tekhnologiya metallov. 2022. No. 12. pp. 43–51.
2. Kozhevnikov A. V., Shalaevsky D. L., Kozhevnikova I. A., Bolobanova N. L. Calculation of structural deformation zone and energy-power parameters during continuous cold rolling of wide steel strips. Certificate of registration of a computer program RU 2019662633. Applied: 02.08.2019. Published: 27.09.2019.
3. Kozhevnikova I. A., Garber E. A. Development of the theory of thin-sheet rolling to improve the efficiency of wide-strip mills: Monograph. Cherepovets : GOU VPO "ChGU", 2010. 275 p.
4. Garber E. A., Kuvshinnikov O. A., Shadrunova I. A. et al. Analysis of energy-power parameters of the process of hot rolling of wide strips with a thickness of 0.8-1.5 mm. Proizvodstvo prokata. 2004. No. 4. pp. 11–16.
5. Garber E. A. Distribution of contact stresses along the deformation zone length when rolling thin wide strips. Proizvodstvo prokata. 2005. No. 5. pp. 3–12.
6. Salganik V. M., Meltser V. V. Computer study of deformations and loads of the quarto roll system: Textbook. Sverdlovsk : UPI, 1987. 78 p.
7. Salganik V. M., Poletskov P. P. Modeling of deformations and loads of the quarto roll system and improvement of the quality of rolled sheets along the profile: Monograph. Magnitogorsk : GOU VPO "MGTU", 2009. 133 p.
8. Gonçalves J. L., de Mello J. D. B., Costa H. L. Wear in cold rolling milling rolls: A methodological approach. Wear. 2019. Vols. 426–427. Part B. pp. 1523–1535. DOI: 10.1016/j.wear.2018.12.005
9. Nikolaev V. A., Vasiliev A. G. Study of inter-roll contact parameters in a quarto stand. Stal. 2021. No. 1. pp. 21–26.
10. Shen Sh., Guye D., Ma X., Yue S., Armanfard N. Multistep networks for roll force prediction in hot strip rolling mill. Machine Learning with Applications. 2022. Vol. 7. 100245. DOI: 10.1016/j.mlwa.2021.100245
11. Baranov G. L. Refined method for calculation of contact stresses during cold strip rolling. Stal. 2022. No. 9. pp. 16–20.
12. Salehebrahimnejad B., Doniavi A., Moradi M., Shahbaz M. Investigation of the initial residual stress effects on a work roll maximum in-service stress in hot rolling process by a semi-analytical method. Journal of Manufacturing Processes. 2023. Vol. 99. pp. 53–64. DOI: 10.1016/j.jmapro.2023.04.084
13. Chen Wei, Shouxu Song, Zhixu Zhang. Evaluation of elastic-plastic deformation in HSS work roll under coupling of residual stress thermal stress and contact stress during hot rolling. Materials Today. 2022. Vol. 33. 104613. DOI: 10.1016/j.mtcomm.2022.104613
14. Antonov P. V., Bolobanova N. L., Kozhevnikova I. A. Modeling of stresses and strains of the roll system of a wide-band cold rolling mill based on the finite element method. Stal. 2019. No. 5. pp. 28–32.
15. Antsupov A. V. (Jr.), Antsupov A. V., Antsupov V. P. Energy-mechanical concept of predicting the durability of friction units based on the criterion of wear resistance of elements. Trenie i iznos. 2016. No. 37 (5). pp. 494–499. DOI: 10.3103/S1068366616050032
16. Kragelsky I. V., Dobychin M. N., Kombalov V. S. Fundamentals of calculations for friction and wear. Moscow : Mashinostroenie, 1977. 526 p.
17. Antsupov A. V. (Jr.), Antsupov A. V., Antsupov V. P. et al. Model of parametric failures of quarto roll systems according to various criteria. Proizvodstvo prokata. 2015. No. 2. pp. 35–42.
18. Polukhin P. I., Nikolaev V. A., Polukhin V. P. et al. Contact interaction of metal and tool during rolling. Moscow : Metallurgiya, 1974. 200 p.
19. Virabov R. V. Traction properties of friction gears. Moscow : Mashinostroenie, 1982. 263 p.
20. Antsupov A. V. (Jr.), Slobodyansky M. G. Forecasting the durability of support rolls and assessing the effectiveness of methods for extending their service life. Vestnik MGTU imeni G. I. Nosova. 2011. No. 3. pp. 74–79.

Language of full-text russian
Full content Buy