Journals →  CIS Iron and Steel Review →  2023 →  #2 →  Back

Metal Science and Metal Physics
ArticleName Study of phase and structural transformations in overcooled austenite for high-strength cold resistant steel during continuous cooling
DOI 10.17580/cisisr.2023.02.13
ArticleAuthor Yu. Yu. Efimova, D. G. Emaleeva, A. E. Gulin, P. G. Adishchev.
ArticleAuthorData

Nosov Magnitogorsk State Technical University (Magnitogorsk, Russia)

Yu. Yu. Efimova, Cand. Eng., Associate Prof., Dept. of Material Material Processing Technology
D. G. Emaleeva, Cand. Eng., Associate Prof., Dept. of Material Material Processing Technology
A. E. Gulin, Cand. Eng., Associate Prof., Dept. of Material Processing Technology, e-mail: a.gulin@magtu.ru
P. G. Adishchev, Post-Graduate, Dept. of Material Material Processing Technology

Abstract

Essential part of strategic objects in oil/gas and machine-building complexes, transport industry and bridge building are operated in the conditions of simultaneous effect of low temperatures, static and dynamic loads as well as intensive wear. High-strength cold-resistance steels are considered as one of the materials, which can be used in such conditions. At present time, providing of principally new qualitative combination of properties of such steels is the actual scientific problem; the main parameters of these steels should be superior to the existing international analogues, they should present the unique combination of high strength, ductility as well as wear and cold resistance at the temperatures down to –70 °C. However, improvement of strength properties and hardness of rolled products leads to substantial decrease of cold resistance and ductility of steel; so, reaching of combination between high strength state and cold resistance is possible during definite structural and phase transformations, occurring in steels. Regularities of phase and structural transformations, occurring in high-strength cold-resistant steel with the following chemical composition (%, mass.): 0.15 C; 1.5 Mn; 0.20 Si; 1.7 (Ni+Cu); 0.035 (Ti+V+Nb); 0.0040 B during continuous cooling, were established in this research. Thermokinetic diagram of decomposition of overcooled austenite was built. It is shown, that steel with above-mentioned composition, which contains mainly if lathe martensite with small amount of bainite, is forming during continuous cooling with rate within the range 10-110 °С/с. Most part of martensite with lathe morphology can provide high strength of the researched steel, presence of dispersed structure of low-carbon bainite can provide high characteristics of resistance to brittle destruction, and hardness more than 350 HBW, which is achieved during cooling with rate more than 50 °С/с can provide high wear resistance.

The research was carried out in the Nosov Magnitogorsk State Technical University at the cost of the grant of Russian scientific fund No. 23-19-20018 dated 20.04.2023, as well as under financial support of the Ministry of Education and Science of Chelyabinsk region (Agreement No 588 dated 29.06.2023), https://rscf.ru/project/23-19-20018/.

keywords High-strength cold-resistance steel, continuous cooling, phase transformations, structure, hardness, thermokinetic diagram
References

1. Strategy of the RF Arctic area development and providing of national security until 2035. Decree of the President of Russian Federation No. 645 dated 26.10.2020. URL: http://publication.pravo.gov.ru/Document/View/0001202010260033?index=1 (reference date 05.07.2023).
2. Strategy of the RF iron and steel industry development during 2014-2020 and prospective-ly until 2030. Decree of the RF Ministry of Industry and Trade No. 839 dated 05.05.2014. URL: https://www.garant.ru/products/ipo/prime/doc/70595824/#1000 (reference date 05.07.2023).
3. Khlusova E. I., Sych O. V. Development of cold-resistant structural materials for Arctic. History, experience, current state. Innovatsii. 2018. No. 11 (241). pp. 85-92.
4. Chukin M. V., Poletskov P. P., Nabatchikov D. G. et al. Analysis of technical requirements to ultra cold-resistant rolled sheets. Vestnik Yuzhno-Uralskogo gosudarstvennogo universiteta. Seriya: Metallurgiya. 2017. Vol. 17. No. 2. pp. 52-60.
5. Poletskov P. P., Gulin A. E., Emaleeva D. G. et al. Analysis of actual directions of the re-searches in the area of production of multi-functional materials for extremal operation conditions. Vestnik Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta im. G. I. Nosova. 2021. Vol. 19. No. 3. pp. 109-114
6. Chukin M. V., Poletskov P. P., Gushchina M. S., Kuznetsova A. S., Nikitenko O. A., Ale-kseev D. Yu. Development of the import-substituting technology for rolled sheet production from high-strength structural steel for Arctic application. Proizvodstvo prokata. 2019. No. 4. pp. 5-11.
7. High-strength steel Strenx®. URL: http://www.ssab.com (reference date 05.07.2023).
8. Extra high-strength sheets sheared from hot-rolled steel strip. URL: https://www.voestalpine.com/alform/en/Products/xtreme (reference date 05.07.2023).
9. High-strength steel sheets QUEND. URL: https://qt.nlmk.com/ru/products/quend/ (refer-ence date 05.07.2023).
10. Wear-resistant steels QUARD. https://qt.nlmk.com/ru/products/quard/ (reference date 05.07.2023).
11. Buznik V. M., Vasilevich N. I. Materials for development of the Arctic territories – chal-lenges and solutions. Laboratoruya i proizvodsto. 2020. No. 1 (11). pp. 98-107.
12. JFE Steel Corporation catalog. URL: https://www.jfe-steel.co.jp/en/products/plate/catalog/c1e-001.pdf (reference date: 05.07.2023).
13. Dillinger proprietary steels. URL: https://www.dillinger.de/d/en/products/heavyplate/highstrength-finegrained/index.shtml (reference date: 05.07.2023).
14. Popova L. E., Popov A. A. Diagrams of austenite transformation in steels and beta-solution in titanium alloys. Moscow: Metallurgiya. 1991. 503 p.
15. Bian J., Mohrbacher H. Novel alloying design for press hardening steels with better crash performance. Int. Symposium on New Developments in AHSS. 2013. PR-294-026.
16. Tarasov G. F., Gorbulya A. I. Heat treatment of steels as a factor of rising their wear re-sistance at low temperatures. Vestnik Sibirskogo gosudarstvennogo aerokosmicheskogo universiteta im. Akademika M. F. Reshetneva. 2005. No. 3. pp. 253-257.
17. Aguiari M., Palombo M., Rizzo C. M. Performance characterization of high-strength steel and quenched and tempered steels and their joints for structural applications. Welding in the World. 2021. Vol. 65. pp. 289–300.
18. Barényi I., Híreš O., Lipták P. Changes in Mechanical Properties of Armoured UHSLA Steel ARMOX 500 After Over Tempering. Problems of Mechatronics, Armament, Aviation, Safety Engineering. 2013. No. 4 (14). pp. 7-14.
19. Shilyaev P. V., Bogach D. I., Krasnov M. L. et al. Mechanical properties and structural state of rolled sheets from high-strength wear-resistant weldable steel H500 MAGSTRONG. Metallovedenie i termicheskaya obrabotka metallov. 2020. No. 11 (785). pp. 8-12.
20. Poletskov P. P., Yakovleva I. V., Koptseva N. V. et al. Examination of the structure and properties of the new cold-resistant high-strength steel, which is operated in the conditions of intensive wear. Metallovedenie i termicheskaya obrabotka metallov. 2021. No. 11 (797). pp. 32-38.
21. Khlusova E. I., Sych O. V., Orlov V. V. Cold-resistant steels. Structure, properties, technologies. Fizika metallov i metallovedenie. 2021. Vol. 122. No. 6. pp. 621-657.
22. Kazakov A. A., Kiselev D. V., Sych O. V., Khlusova E. I. The technique for assessment of microstructural heterogeneity across thickness of plate made of cold-resistant low-alloy steel for Arctic applications. Chernye metally. 2020. No. 9. pp. 11-19.
23. Poletskov P. P., Koptseva N. V., Efimova Yu. Yu., Kuznetsova A. S. Influence of heat treatment on forming the complex of properties for high-strength cold-resistance. CIS Iron and Steel Review. 2023. Vol. 25. pp. 73–78.

Full content Study of phase and structural transformations in overcooled austenite for high-strength cold resistant steel during continuous cooling
Back