Journals →  Chernye Metally →  2022 →  #12 →  Back

55 years of the Department of Materials Science and Materials Technology of Orenburg State University
ArticleName Analysis of the cause of destruction of the repair welded joint of a coiled tubing pipe
DOI 10.17580/chm.2022.12.06
ArticleAuthor V. S. Repyakh, A. A. Kirichenko, V. M. Kushnarenko, V. I. Yurshev.
ArticleAuthorData

Orenburg State University, Orenburg, Russia:

V. S. Repyakh, Cand. Eng., Associate Prof., Dept. of Materials Science and Technology (MS&T), e-mail: podval2004@mail.ru
V. M. Kushnarenko, Dr. Eng., Prof., Dept. of MS&T, e-mail: vmkushnarenko@mail.ru
V. I. Yurshev, Cand. Eng., Associate Prof., Head of the Dept. of MS&T, e-mail: yvi170858@rambler.ru

 

ESTM Ltd, Tula, Russia:

A. A. Kirichenko, Quality Director, e-mail: a.kirichenko@estm-tula.com

Abstract

The article presents the results of studies of the destruction of coiled tubing after repair with the formation of a transverse weld using fusion welding without subsequent heat treatment. The design features of the repair welded joint are considered. A description of the operating conditions of the tubing is presented – ambient temperature, working fluid temperature, pressure, working fluid flow rate, number of round trips, as well as the characteristics of the working environment containing chloride salts, hydrochloric acid solution and gaseous nitrogen (with a high percentage oxygen content). To determine the cause of the failure and identify the corresponding defects, the method of visual-measuring control, determination and analysis of the results of measurements of the hardness and chemical composition of the material of the pipe and weld, mechanical tests were used. Particular attention was paid to fracture analysis, detection of defects in the form of pores, as well as metallographic studies of the microstructure of the welded joint. The ability to use manual arc welding for pipe repair in case of failure, as well as the identification of possible defects obtained during the repair and operation of coiled tubing, allows you to more quickly repair equipment and ensure an increase in its service life, eliminating unwanted downtime. The use of additional heat treatment and well-prepared surfaces for welding by cleaning and degreasing has a significant impact on the quality of the welded joint and leads to minimal formation of defects (pores, microcracks) that affect the further operation of the equipment as a whole, operated under tensile stress conditions during repeated static bending coiled tubing.

keywords Coiled tubing, fusion welding, welded joint, defects, microstructure, destruction
References

1. Organization standard STO 9701105632-003–2021. Instructions for visual and measuring control.
2. RD 50-672–88. Methodical instructions. Calculations and strength tests. Classification of types of fractures of metals. Moscow: Gosstandart, 1989. 22 p.
3. Fellows J. Fractography and atlas of fractographs: handbook. Translated from English. Moscow: Metallurgiya, 1982. 89 p.
4. GOST 18895–97. Steel. Method of photoelectric spectral analysis. Introduced: 01.01.1998.
5. GOST 9013–59. Metals. Method of measuring Rockwell hardness. Introduced: 01.01.1969.
6. GOST 1497–84. Metals. Methods of tension test. Introduced: 01.01.1986.
7. Kushnarenko V. М., Chirkov Yu. А., Polishchuk V. Yu., Repyakh V. S. The Physical nature of destruction: study guide. Orenburg: OGIM, 2014. 369 p.
8. Kushnarenko V. М., Repyakh V. S., Chirkov E. Yu., Kushnarenko Е. V. Defects and damage to parts and structures: monograph. Orenburg: Russervis Ltd., 2012. 531 p.
9. Kushnarenko V. М., Repyakh V. S., Kushnarenko Е. V., Chirkov E. Yu. Analysis of the causes of equipment and pipeline failures. Vestnik OGU. 2010. No. 10. pp. 153–159.
10. Chirkov Yu. А., Kushnarenko V. М., Repyakh V. S., Chirkov E. Yu. Causes of destruction of welded joints of flexible tubing pipes. Metallovedenie i termicheskaya obrabotka metallov. 2017. No. 10 (748). pp. 54–58.
11. Egorov Yu. P., Strelkova I. L., Baginskiy А. G. Investigation of the destruction of the threaded connection of the tubing pipe. Neftyanoe khozyaystvo. 2018. No. 1. pp. 82–84.
12. Petrov V. S., Vasin R. А., Knyazeva Zh. V., Andriyanov D. I., Surgaeva Е. S. Corrosion destruction of the metal of oil and gas pipelines during operation and during laboratory tests. Neftegazovoe delo. 2020. Vol. 18. No. 4. pp. 102–112.
13. Amezhnov А. V., Rodionova I. G., Stukalova N. А., Antoshenkov А. Е., Gladchenkova Yu. S. Establishing the causes of premature corrosion failure of the tubing pipe. Problemy chernoy metallurgii i materialovedeniya. 2020. No. 4. pp. 68–79.
14. GOST 1778–70. Steel. Metallographic methods for the determination of nonmetallic inclusions. Introduced: 01.01.1972.
15. ANSI/NACE MR0175/ISO 15156-3:2015. Oil, petrochemical and gas industry. Materials for use in hydrogen sulfide environments in oil and gas production. Part 3: CRA (corrosion-resistant alloys) and other crack-resistant alloys.

Language of full-text russian
Full content Buy
Back