Journals →  Chernye Metally →  2022 →  #10 →  Back

Power Engineering
ArticleName Development of an improved automatic control algorithm for combined RCB burners and carbonaceous material injectors of a flexible modular furnace
DOI 10.17580/chm.2022.10.11
ArticleAuthor A. A. Nikolaev, P. G. Tulupov, S. S. Ryzhevol
ArticleAuthorData

Nosov Magnitogorsk State Technical University, Magnitogorsk, Russia:

A. A. Nikolaev, Cand. Eng., Associate Prof., Head of the Dept. of Automatic Electric Drive and mechatronics, e-mail: aa.nikolaev@magtu.ru
P. G. Tulupov, Cand. Eng., Junior Researcher, Dept. of Automatic Electric Drive and mechatronics, e-mail: tulupov.pg@mail.ru
S. S. Ryzhevol, Postgraduate Student, Dept. of Automatic Electric Drive and mechatronics, e-mail: snaffls18@gmail.com

Abstract

The control algorithm for combined ceramic regenerative burners (Regenerative Ceramic Burner, RCB) and carbon-containing material injectors of a flexible modular arc steel-smelting furnace DSP-1 operating at one of the domestic metallurgical enterprises is considered. It was revealed that in the concept adopted in production, the decision to switch the RCB burner from the burner mode to the oxygen lance mode, as well as to turn on the carbon-containing material injectors, is made directly by the operator of the furnace plant based on a set of empirical features characteristic of one or another technological stage of melting. In this regard, an improved control algorithm for RCB burners and carbon-containing material injectors has been developed and proposed for implementation, which will ensure the adoption of the above-mentioned decisions in automatic mode. This algorithm is based on the analysis of the slag coefficient, the value of which directly depends on the level of higher harmonics in the spectrum of electric arc current signals, as well as physical processes occurring inside the furnace bath. The implementation of the proposed algorithm enables to achieve the most timely adaptation of operating modes of combined burners and carbon-containing material injectors, which in turn will increase the overall energy efficiency of the steelmaking complex as a result of an increase in the total thermal efficiency of electric arcs and the optimal operating mode of the burners.
This work was supported financially by the Ministry of Science and Higher Education of the Russian Federation (Project No. FZRU-2020-0011).

keywords Electric arc furnace, flexible modular furnace, RCB burner, carbonaceous material injector, electrical mode, control algorithm
References

1. Boulet B., Lalli G., Ajerschv M. Modeling and control of an electric arc furnace. Proceedings of the American Control Conference, Denver, Colorado, 2003.
2. Hay T., Hernandez J., Roberts S., Echterhof T. Calculation of view factors in electric arc furnace process modeling. Steel Research International. 2020. Vol. 92, Iss. 2. p. 2000341.
3. Panoiu M., Panoiu C., Ghiormez L. Modeling of the electric arc behaviour of the electric arc furnace. 5th International Workshop on Soft Computing Applications, Szeged, Hungary. 2012. pp. 261–271.
4. Nikolaev А. А., Tulupov P. G., Malakhov О. S., Ryzhevol S. S. Improvement of the efficiency of control systems for electric modes of electric arc furnaces through the use of an adaptive impedance controller. Vestnik Yuzhno-Uralskogo gosudarstvennogo universiteta. Seriya «Energetika». 2021. Vol. 21. No. 4. pp. 82–93.
5. Wang Yan, Mao Zhi-zhong, Tian Hui-xin, Li Yan, Yuan Ping. Modeling of electrode system for three-phase electric arc furnace. J. Cent. South Univ. Technol. 2010. Vol. 17. pp. 560–565.
6. Nikolaev A. A., Tulupov P. G., Lozhkin I. A. Development and research of improved control algorithms for electric modes of a shaft-type electric arc furnace. Proceedings of the 2020 Russian Workshop on Power Engineering and Automation of Metallurgy Industry: Research & Practice (PEAMI 2020). Magnitogorsk, Russia. 2020. pp. 1–6.
7. Nikolaev A. A., Tulupov P. G., Anufriev A. V. Assessing the feasibility of electrical mode control of ultra-high power arc steelmaking furnace based on data about harmonic composition of arc currents and voltages. Proceedings of 16th International Conference on Research and Education in Mechatronics (REM2015). IEEE. Bochum, Germany, 2015. pp. 302–308.
8. Mironov Yu. М. Electric arc in electrotechnological installations: monograph. Cheboksary: Izdatelstvo Chuvashskogo Universiteta, 2013. 290 p.
9. Makarov А. N. The laws of heat transfer of an electric arc and a torch in metallurgical furnaces and power plants. Tver: Izdatelstvo Tverskogo gosudarstvennogo tekhnicheskogo universiteta, 2012. 164 p.
10. Nekhamin S. М. Creation and implementation of energy-efficient arc and slag electric furnace complexes using direct current and low-frequency current: Dissertation … of Doctor of Engineering Sciences. Moskovskiy energeticheskiy institut, Moscow. 2015.
11. Svenchanskiy А. D., Zherdev I. Т., Kruchinin А. М. et al. Electrical industrial furnaces: arc furnaces and special heating installations: textbook for universities. Edited by A. D. Svenchansky. Moscow: Energoizdat, 1981. 296 p.
12. Krüger K. Modellbildung und regelung der elektrischen energieumsetzung von lichtbogenöfen (Modeling and control of the electrical energy conversion in arc furnaces). Dr.-Ing. Dissertation,Fachbereich Maschinenbau, Universität der Bundeswehr Hamburg, Fortschritt-Berichte VDI. Reihe 6, Nr. 382. VDI-Verlag, Düsseldorf. 1998.
13. Nikolaev А. А., Tulupov P. G., Omelchenko Е. Ya. Experimental studies of the harmonic composition of currents and voltages of arcs in a powerful arc steel-smelting furnace of shaft type. Elektrotekhnicheskie sistemy i kompleksy. 2018. No. 4 (41). pp. 63–72.
14. Nikolaev A. A., Tulupov P. G., Agapitov E. B. Method of switching point determination for control system of electric arc furnace based on data about harmonics of arc currents and voltages. 2020 International Conference on Industrial Engineering, Applications and Manufacturing (ICIEAM). 2020. pp. 1–5.
15. Jansen Т., Krueger К., Schliephake H. et al. DC-EAF power control using a sound based foaming slag signal. Chernye Metally. 2011. No. 2. pp. 20–25.

Language of full-text russian
Full content Buy
Back