Journals →  Tsvetnye Metally →  2020 →  #11 →  Back

HEAVY NON-FERROUS METALS
ArticleName Processing of metallurgical dusts in sulfate-nitrate solutions
DOI 10.17580/tsm.2020.11.03
ArticleAuthor Naboychenko S. S., Kovyazin A. A., Timofeev K. L., Krayukhin S. A.
ArticleAuthorData

Ural Federal University named after the First President of Russia B. N. Yeltsin, Yekaterinburg, Russia:

S. S. Naboychenko, Visiting Professor at the Department of Non-Ferrous Metallurgy, Doctor of Technical Sciences, Professor, Corresponding Member of Russian Academy of Sciences

 

JSC “Uralelektromed”, Verkhnyaya Pyshma, Russia:
A. A. Kovyazin, Process Engineer of the Research Centre, e-mail: A.Kovyazin@elem.ru
K. L. Timofeev, Head of Research Centre, Candidate of Technical Sciences, e-mail: К.Timofeev@elem.ru

 

UMMC Тechnical University, Verkhnyaya Pyshma, Russia:
S. A. Krayukhin, Director of Science, Candidate of Technical Sciences, e-mail: s.krauhin@tu-ugmk.com

Abstract

The composition of fine dusts of copper smelting enterprises contains zinc, copper, lead, which are of practical interest for their subsequent use in metallurgical processing, and arsenic, which is the main impurity and requires purification. For the processing of polymetallic middling products, various physicochemical processes are used — pyrometallurgical, hydrometallurgical, electro-chemical, having both advantages and disadvantages. One of the promising ways to extract valuable components into a solution, followed by selective conversion to cognominal products, is the considered sulfur — nitric acid technology. The implementation of such a scheme allows not only to achieve a high degree of extraction of valuable components from dust, but also to obtain monocomponent products suitable for further processing with the production of pure metals. Under laboratory conditions, regularities in the recovery of non-ferrous metals from the consumption of nitric acid were determined. The main parameters of the processing of metallurgical dust according to the sulfuricnitric acid scheme were selected. Experiments on sulfur-nitric leaching were carried out at a sulfuric acid concentration of 100 g/dm3, temperature 80 оC, L:S = 1:3 ratio, duration 3 hours, consumption of nitric acid varied from 0 to 0.7 g/g. The proposed technology allows in one stage to obtain Zn – As – Cu solutions that are suitable for processing with receiving individual products. The scheme provides for the return of nitrate-containing solutions to the leaching of sulfide material, which significantly increases the utilization rate of nitric acid. The main operations of the technology are: neutral leaching, sulfuric acid leaching, nitrate leaching, arsenic precipitation, copper precipitation as sulfide with return of part of Cu – As cake for conditioning it by copper and removal of arsenic. On the basis of the conducted research, the optimal parameters for the processing of metallurgical dusts for the selective separation of copper, zinc, lead and arsenic were established.

keywords Dust, copper, zinc, arsenic, lead, leaching, nitric acid, utilization of arsenic
References

1. Panshin A. M. Complex processing of zinc-containing industrial products of non-ferrous metallurgy : Thesis of Inauguration of Dissertation … of Doctor of Technical Sciences. Yekaterinburg, 2013. 41 p.
2. Khrennikov A. A., Dubrovin P. V., Vasilyev E. A. et al. Technology of arsenic removal from the metallurgical cycle of the Mednogorsk copper-sulfur plant. Tsvetnye Metally. 2008. No. 11. pp. 71–73.
3. Karelov S. V., Naboychenko S. S., Mamyachenkov S. V. et al. Complex processing of zinc- and lead-containing dusts of non-ferrous metallurgy enter prises. Moscow : TsNIIEITSM, 1996. 40 p.
4. Vlasov O. A. A method of processing lead-zinc concentrates. Patent RF, 2486267. Published 27.06.2013. Bulletin No. 18.
5. Shumskiy V. A., Ushakov N. N., Startsev I. V. et al. Aggregate for processing powdered lead and zinc-containing raw materials. Patent RF, 2359188. Published 20.06.2009. Bulletin No. 17.
6. Letov A. V., Kan A. V. Method for processing lead-containing waste. Patent RF, 2294972. Published 10.03.2007. Bulletin No. 7.
7. Geykhman V. V., Tarasov A. V., Kazanbaev L. A. et al. A method of processing zinc and copper-containing lead cakes and dusts. Patent RF, 2150520. Published. 10.06.2000.
8. Lanzerstorfer C. Flowability of various dusts collected from secondary copper smelter off-gas. Particuology. 2016. Vol. 25. pp. 68–71.
9. Isabaev S. M., Kuzgibekova Kh. M., Zikanova T. A., Zhinova E. V. Complex hydrometallurgical processing of lead arsenic-containing dust from copper production. Tsvetnye Metally. 2017. No. 8. pp. 33–37.
10. Ivanov B. Ya., Yaroslavtsev A. S., Vanyushkina G. N. Hydrometallurgical processing of fine converter dusts of copper-smelting production. Tsvetnye Metally. 1982. No. 4. pp. 16–21.
11. Jarošíková А., Ettler V., Mihaljevic M., Drahota P., Culka A., Racek M. Characterization and pH-dependent environmental stability of arsenic trioxide-containing copper smelter flue dust. Journal of Environmental Management. 2018. Vol. 209. pp. 71–80.
12. Jarošíková А., Ettler V., Mihaljevic M., Penížek V., Drahota P. Transformation of arsenic-rich copper smelter flue dust in contrasting soils: A 2-year field experiment. Environmental Pollution. 2018. Vol. 237. pp. 83–92.
13. Montenegro V., Sano H., Fujisawa T. Recirculation of high arsenic content copper smelting dust to smelting and converting processes. Minerals Engineering. 2013. Vol. 49. pp. 184–189.
14. Sequeira C. A. C., Marquis F. D. S. Zinc pressure leaching. Chemistry, Energy and the Environment. 1998. P. 135–149.
15. Liu W., Li Z., Han J. et al. Selective separation of arsenic from lead smelter flue dust by alkaline pressure Oxidative leaching. Minerals. 2019. Vol. 9. pp. 308.
16. Rogozhnikov D. A. Complex hydrometallurgical processing of multicomponent sulfide by-products : Thesis of Inauguration of Dissertation … of Candidate of Technical Sciences. Yekaterinburg, 2013. 22 p.

Language of full-text russian
Full content Buy
Back