Журналы →  Tsvetnye Metally →  2020 →  №4 →  Назад

Название Evolution of structure, crystallographic texture and mechanical properties in innovative titanium alloys during plastic deformation and heat treatment
DOI 10.17580/tsm.2020.04.07
Автор Isaenkova M. G., Perlovich Yu. A., Babich Ya. A., Medvedev P. N.
Информация об авторе

National Research Nuclear University MEPhI, Moscow, Russia:

M. G. Isaenkova, Professor, Doctor Physics & Mathematics Sciences, e-mail: isamarg@mail.ru
Yu. A. Perlovich, Professor, Doctor of Physics & Mathematics Sciences

Ya. A. Babich, Postgraduate Student


All-Russian Scientific Research Institute of Aviation Materials, Moscow, Russia:
P. N. Medvedev, Sector Chief, Candidate of Physics & Mathematics Sciences


Titanium alloys, in spite of their low density, are characterized by high mechanical strength, corrosion resistance, creep resistance at elevated temperatures, heat resistance and manufacturability. A further increase in operational characteristics necessitates the development of new alloys. The presence in alloys of alpha-titanium, that is their low-temperature modification, characterizing by anisotropy of a crystalline hexagonal close-packed structure, predetermines the interest to predominant crystallographic orientations of grains in products. This work is devoted to the analysis of plastic deformation and heat treatment influence on the structure, crystallographic texture and mechanical properties of promising titanium alloys VT18U, VT41 and VT25U. The studied alloys belong to their different types: the first two ones are pseudo-α-alloys, and the last one — (α + β)-alloy. Sheet samples were subjected to hot rolling and subsequent heat treatment in order to identify the influence of technological parameters on the formation of phase state and crystallographic texture of the alloys. The structure and texture of materials were studied by metallographic and X-ray methods. The phase composition of alloys was determined and their texture was analyzed by constructing direct pole figures and restoring orientation distribution functions of grains. The measurement of mechanical properties was carried out using continuous indentation curves. As a result of the study, the basic regularities of crystallographic texture formation during hot rolling and subsequent phase transformations as applied to alloys of various types have been revealed. It was found that the main texture components of hot rolled sheets are {0001}±15–20o ND-RD<112L>, {110}<100> and {110}<0001>, the ratios between which depend on the type of alloy. The mechanisms that determine the formation of texture during hot rolling were established. The limits of variation of the integral texture parameters for hotrolled titanium pseudo-α and (α + β)-alloys have been revealed, and the anisotropy coefficients of yield strengths for alloys with textures of different types have been calculated.
The research was conducted under financial support of the State Program for elevation of competitiveness in the National Research Nuclear University "MEPHI" (Agreement No. 02.a03.21.0005).

Ключевые слова Titanium alloys, hot rolling, texture, anisotropy, pole figure, ODF, annealing, hardening, phase transformation
Библиографический список

1. Lutjering G., Williams J. C. Titanium. Berlin. Springer–Verlag. 2007. 449 p.
2. Zwicker U. Titanium and its alloys. Translated from German. Moscow : Metallurgiya, 1979. 512 p.
3. Arzamasov B. N., Brostrem V. A., Bushe N. A. et al. Structural materials: Reference book. Moscow : Mashinostroenie, 1990. 688 p.
4. Inozemtsev A. A., Bashkatov N. G., Koryakovtsev A. S. Modern titanium alloys and the problems of their development. Moscow : VIAM, 2010. pp. 43–45.
5. Glazunov S. G., Yasinskiy K. K. Titanium alloys for aviation and other industries. Tekhnologiya splavov. 1993. No. 7–8. pp. 1–14.
6. Pavlova T. V., Kashapov O. S., Nochovnaya N. A. Titanium alloys for gas turbine engines. Moscow : VIAM, 2011. pp. 1–15.
7. Solonina O. P., Glazunov S. G. Advanced heat-resistant titanium alloys and their prospective application in engines. Moscow : Metallurgiya, 1974.
8. Materials Properties Handbook: Titanium Alloys. Ed. by Boyer R., Collings E. W., Welsch G. ASM, Materials Park, USA, 1994. 1169 p.
9. Vishnyakov Ya. D., Babareko A. A., Vladimirov S. A. et al. Theory of texture formation in metals and alloys. Moscow : Nauka, 1979. 344 p.
10. Kocks U. F., Tome C. N., Wenk H.-R. Texture and Anisotropy. Preferred orientation in polycrystals and their effect on materials properties. Cambridge University Press, 1998. 676 p.
11. Isaenkova M. G., Perlovich Yu. A. Evolution of crystallographic texture and substructural heterogeneity in zirconium alloys under deformation and heat treatment. Moscow : NIYaU MIFI, 2014. 528 p.
12. Shikov A. K., Bocharov O. V., Arzhakova V. M., Bezumov V. N., Perlovich Yu. A. et al. Use of hafnium in control elements of nuclear reactors and power units. Metal Science and Heat Treatment. 2003. Vol. 45, Iss. 7-8. pp. 300–303.
13. Adamesku R. A., Alsagarov A. A., Kaganovich A. Z. et al. Effect of the production technique on the texture and mechanical anisotropy in VT6S alloy sheets. Tsvetnye Metally. 1979. No. 1. pp. 59–64.
14. Skryabin D. A., Adamesku R. A., Kochegarova G. B. How the rolling technique influences the recrystallisation texture in VT1-0 and OT4-1 alloys. Tekhnologiya legkikh splavov. 1978. No. 6. pp. 51–57.
15. Alsagarov A. A., Adamesku V. A., Geld P. F. Formation of rolling and recrystallisation textures in titanium and zirconium. Bulletin of the Academy of Sciences of the USSR. Metals Series. 1977. No. 2. pp. 139–143.
16. Babareko A. A., Egiz I. V. Texture formed in titanium alloys during deformation-induced martensitic transformations. Fizika metallov i metallovedenie. 1990. No. 2. pp. 134–139.
17. Egiz I. V., Babareko A. A. Twin orientations formed in the structure of α-titanium during elongation and rolling. Bulletin of the Russian Academy of Sciences. Metals. 1993. No. 2. pp. 160–164.
18. Isaenkova M. G., Perlovich Yu. A., Fesenko V. A., Saveliev I. I. Texture formation in dual-phase titanium alloys during cold rolling. Problems of producing ingots and semi-products from complex alloyed and intermetallic titanium alloys: Conference proceedings. 30 October 2015.
19. Engler O., Randle V. Introduction to texture analysis. Macrotexture, microtexture and orientation mapping. Second Edition. CRC Press, 2010. 488 p.
20. Chun Y. B., Yu S. H., Semiatin S. L., Hwang S. K. Effect of deformation twinning on microstructure and texture evolution during cold rolling of CP-titanium. Materials Science and Engineering A. 2005. Vol. 398, Iss. 1-2. pp. 209–219.
21. Bozzollo N., Dewobroto N., Wenk H. R., Wagner F. Microtexture and microstructure of highly colled-rolled commercially pure titanium. Journal of Materials Science. 2006. Vol. 42. pp. 2405–2416.
22. Gerspach F., Bozzolo N., Wagner F. On the stability of recrystallization texture in low alloyed titanium sheets. Application of Texture Analysis, Ceramic Transactions. 2008. Vol. 201. pp. 593–600.
23. Pawlik K. Determination of the orientation distribution function from pole figures in arbitrarily defined cells. Physica status solidi (b). 1986. Vol. 134, Iss. 2. pp. 477–483.
24. Jura J., Pospiech J. The Determination of orientation distribution function from incomplete pole figures. Textures of Crystalline Solids. 1978. Vol. 3, Iss. 1. pp. 1–25.
25. Isaenkova M., Perlovich Yu. A., Fesenko V. Modern methods of experimental construction of texture complete direct pole figures by using X-ray data. IOP Conference. Series: Materials Science and Engineering. 2016. Vol. 130. 012057. DOI: 10.1088/1757-899X/130/1/012055.
26. Isaenkova M. G., Perlovich Yu. A., Krymskaya O. A., Fesenko V. A., Babich Y. A. Optimization of the procedure for determining integral texture parameters of products from zirconium-based alloys using the orientation distribution function. IOP Conference Series: Materials Science and Engineering. 2016. Vol. 130. 012056. DOI: 10.1088/1757-899X/130/1/012056.
27. Perlovich Yu., Bunge H. J., Isaenkova M. The fullest description of the structure of textured metal materials with generalized pole figures: The example of rolled Zr alloys. Materials Science Forum. 2001. Vol. 378–381. pp. 180–185.
28. Kearns J. J. Thermal expansion and preferred orientation in Zircaloy. WAPD-TM-472, TID-4500. Bettis Atomic Power Lab., Pittsburgh P. A. (USA), 1965.
29. Nye J. Physical Properties of Crystals: Their Representation by Tensors and Matrices. Translated from English. Moscow : Mir, 1967. 385 p.
30. Matsegorin I. V., Evstyukhin A. I., Nikishov O. A., Osipov V. V. Effect of texture on the physical and mechanical anisotropy in channel and cladding tubes made of zirconium alloys. Moscow : MIFI, 1984. 32 p.

31. Golovin Yu. I. Nanoindentation and its capabilities. Moscow : Mashinostroenie, 2009. 311 p.
32. Sakai M. Simultaneous estimate of elastic-plastic parameters in depthsensing indentation tests. Scripta Materials, 2004. Vol. 51. pp. 391–395.
33. Oliver W. C., Pharr G. M. Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. Journal of Materials Research. 2004. Vol. 19, Iss. 1. pp. 3–20.
34. Milman Yu. V., Chugunova S. I., Goncharova I. V. Plasticity characteristic obtained by indentation. Voprosy atomnoy nauki i tekhniki. 2011. No. 4. pp. 182–187.
35. Isaenkova M. G., Perlovich Yu. A., Soe San Thu, Krymskaya O. A., Fesenko V. A. Development of crystallographic texture in the time of rolling or Zr monocrystals and their recrystallization. Tsvetnye Metally. 2014. No 12. рр. 73–78.
36. Isaenkova M., Perlovich Yu. Features of the phase transformations in sheets, tubes and welding seams of the alloy Zr –2,5% Nb. Textures and Microstructures. 1997. Vol. 30. рр. 55–70.
37. Fong R. W. L., Fazeli F., Smith T. Thermal Expansion Anisotropy of Zr – 2,5 Nb Pressure Tube Material on Heating to 1100 °C. 35th Annual Conference of the Canadian Nuclear Society. 2015. рр. 1–12.

Language of full-text русский
Полный текст статьи Получить