Журналы →  Chernye Metally →  2014 →  №2 →  Назад

Development of metallurgy in Russia and CIS
Название Investigation of the effect of cooling rate on forming the structure of wire rod made of 80P steel and intended for manufacture of high-strength reinforced bars
Автор N. V. Koptseva, D. M. Chukin, Yu. Yu. Efimova, O. A. Nikitenko, A. S. Ishimov
Информация об авторе

Magnitogorsk State Technical University named after G. I. Nosov (Magnitogorsk, Russia):

Koptseva N. V., Dr. Eng., Prof., Chair of Casting Production and Material Science, e-mail: koptsev2002@mail.ru
Chukin D. M., Post-Graduate, Chair of Casting Production and Material Science
Efimova Yu. Yu., Cand. Eng., Associate Prof., Chair of Machine-Building and Metallurgical Technologies
Nikitenko O. A., Cand. Eng., Assistant, Chair of Machine-Building and Metallurgical Technologies
Ishimov A. S., Post-Graduate, Chair of Machine-Building and Metallurgical Technologies


Dilatometrical testings of 80P steel, microalloyed with boron, have been conducted using GLEEBLE 3500 research complex. Temperature and time conditions of the experimental procedures during dilatometrical testings provided 4 different techniques with permanent heating rate (30 ºC/s), different holding time (1–3 s) and different cooling rate (1–100 ºC/s). Qualitative and quantitative features of forming its microstructure during continuous cooling with diff erent cooling rate (1.5–80 ºC/s) are established, including HV and HRC hardness distribution. These features take into account technical requirements for wire rod using afterwards for manufacture of reinforced bars. Critical points of forming different types of microstructure (ferrite, pearlite, bainite and martensite) have been determined using dilatometrical curves obtained during continuous cooling. The results of investigations allowed to formulate that it is not possible to prevent forming of excessive ferrite and pseudo-eutectoid sorbite-type structure with interlamellar distance 0.1–0.2 μm at actual cooling rate of 10 mm diameter wire rod after heating before rolling. Therefore, 10 mm diameter wire rod can’t be used for direct drawing in manufacture or wire billet for production of high-strength reinforced bars. It is recommended to use patented billet for reaching the high level of mechanical properties of reinforced bars.

Ключевые слова Steels, heating, rolling, cooling, wire rod, reinforced bars, microstructure, dilatometrical testings, boron, ferrite, pearlite, bainite, martensite
Библиографический список

1. Yukhvets I. A. Proizvodstvo vysokoprochnoy armatury (Manufacturing of high-tensile reinforcement). Moscow : Metallurgiya, 1973. 264 p.
2. Gulyaev A. P., Astafev A. S., Volkova M. A. et al. Vysokoprochnye armaturnye stali (High-tensile reinforcing-bar steels). Moscow : Metallurgiya, 1966. 140 p.
3. Beckenhof H., Schwir F., Rockrohr H. et al. Chernye Metally — Ferrous metals. 1967. No. 6. pp. 11–29.
4. Uzlov I. G., Babich V. K., Parusov. V. V. et al. Stal — Steel in Translation. 1983. No. 11. pp. 77–79.
5. Lebedev V. N., Korchunov A. G., Chukin M. V. Metallurg — Metallurgist. 2011. No. 1. pp. 75–78.
6. Pekhterev S. V., Ivin Yu. A., Nikolaev O. A. et al. Рroduction of highstrength reinforced bar steel for Russian railways. Chernye Metally — Ferrous metals. 2013. No. 6 (978). pp. 27–32.
7. Parusov V. V., Sychkov A. B., Parusov E. V. Teoreticheskie i tekhnologicheskie osnovy proizvodstva vysokoeff ektivnykh vidov katanki (Theoretical and technological basis of production of high-effi cient types of wire). Dnepropetrovsk : ART-PRESS, 2012. 376 p.
8. Rudskoy A. I., Kolbasnikov N. G., Zotov O. G. et al. Chernye Metally — Ferrous metals. 2010. No. 2. pp. 8–14.
9. Chukin D. M., Ishimov A. S., Zherebtsov M. S. Ispolzovanie kompleksa Gleeble 3500 dlya analiza fazovykh prevrashcheniy v stali evtektoidnogo sostava, mikrolegirovannoy borom (Usage of complex Gleeble 3500 for analysis of phase transformations in eutectoid composition steel, microalloyed by boron). Obrabotka sploshnykh i sloistykh materialov: mezhvuzovskiy sbornik nauchnykh trudov (Processing of solid and composite materials: inter-university collection of scientifi c proceedings). Under the editorship of M. V. Chukin. Magnitogorsk: Publishing House of G. I. Nosov Magnitogorsk State Technical University, 2012. Iss. 38. pp. 53–57.
10. Popov A. A. Fazovye prevrashcheniya v metallicheskikh splavakh (Phase transformations in metallic alloys). Moscow : Metallurgizdat, 1963. 311 p.
11. Parusov E. V., Parusov V. V., Evsyukov M. F. et al. Metallurgicheskaya i gornorudnaya promyshlennostMetallurgical and mining industry. 2006. No. 3. pp. 64–67.
12. Parusov V. V., Parusov E. V., Sagura L. V. et al. Metallurgicheskaya i gornorudnaya promyshlennostMetallurgical and mining industry. 2011. No. 3. pp. 53–56.
13. Mezin I. Yu., Chukin V. V. Vestnik Magnitogorskogo Gosudarstvennogo Tekhnicheskogo Universiteta imeni G. I. Nosova — Bulletin of G. I. Nosov Magnitogorsk State Technical University. 2011. No. 4 (34). pp. 30–34.
14. Chukin M. V., Gun G. S., Korchunov A. G., Polyakova M. A. Chernye Metally — Ferrous metals. 2012. No. 12. pp. 8–16.

Language of full-text русский
Полный текст статьи Получить