Journals →  Chernye Metally →  2019 →  #9

Chernye Metally


The Rolling and other Metal Forming Processes section opens the September issue of the journal. Here, the general concept of the channel calibration optimization and the model structure are presented, which makes it possible to use both one general and two different optimality criteria according to the optimization goals at different stages of solving the task. It was shown that some parameters of the cross-sectional profile of a hot-rolled strip can be used to predict the probability of strip breakage during cold rolling. In a final article of this section, dependencies to determine the force on the drawing rollers of the leveling and tempering unit of the continuous galvanizing line were given.


The largest Pipe Production section of the issue contains seven articles. In particular, technical solutions aimed at minimizing the negative impact of sheet-to-pipe stage on product quality characteristics have been proposed. A solution to eliminate metal loss during the setup of the piercing mill, based on the use of modern digital technologies, including BigData and artificial intelligence technologies, was also presented. A new technology for the production of seamless stainless tubes in coils for LNG equipment was proposed. The use of computer modeling methods for predicting the surface quality of pipes and finding ways to reduce crack formation is considered. A study, carried out to establish factors affecting the change in tubes ovality, was described. The possibility of reducing the technological increase to compensate thinning of the wall during stamping of bottoms from carbon and low alloy steels was shown.


The Heating and heat treatment section describes the methodology for studying industrial units based on the Phoenix TM automated system, which allows to improve heating processes and is applied both at domestic and foreign enterprises. From foreign authors` materials, the reader learns about a new annealing line at Bilstein company and about a progressive method, alternative to classical heat treatment, developed by Deutsche Edelstahlwerke.


The Economics and Finance section presents material devoted to the study of the directions of world metallurgical production development, the dynamics of world steel production, as well as the issues of domestic metallurgy modernization.


The From the History of Metallurgy section concludes the issue. It gives a detailed overview of the technology of armored corps production of Third Reich’s tanks, which participated in the battles of World War II.


Please find more details below, or order your printed or electronic version of the Journal.

Rolling and other metal forming processes
ArticleName Optimization of roll calibrations for beam channel rolling. Part 1. General regulations
ArticleAuthors D. L. Shvarts, A. M. Mikhaylenko, E. I. Ustinova

Ural Federal University (Ekaterinburg, Russia):

D. L. Shvarts, Cand. Eng., Associate Prof., Head of the Department “Metal Forming”
A. M. Mikhaiyenko, Cand. Eng., Associate Prof., Department “Metal Forming”
E. I. Ustinova, Assistant, Post-Graduate, E-mail:

ArticleName Application of the saddle coefficient for estimating the quality of a hot-rolled steel strip
ArticleAuthors S. M. Belskiy, I. I. Shopin

Lipetsk State Technical University (Lipetsk, Russia):

S. M. Belskiy, Dr. Eng, Prof., Metall Forming Dept., e-mail:
I. I. Shopin, Cand. Eng., Metall Forming Dept.

ArticleName Calculation of the pulling force of a galvanized strip through the straightening and skin pass rolling unit
ArticleAuthor E. A. Maksimov

Intray JSC (Chelyabinsk, Russia):

E. A. Maksimov, Cand. Eng., e-mail:

ArticleName Efficiency of modern production technologies and quality of large diameter pipes
ArticleAuthor V. G. Ilyichev

South Ural State University (Chelyabinsk, Russia):

V. G. Ilyichev, Cand. Eng., Associate Prof., Dept. “Processes and machines”, e-mail:

ArticleName Determination of piercing mill settings using digital technology
ArticleAuthors D. Yu. Zvonarev, V. L. Neroznikov, A. V. Vydrin

All-Russian Scientific and Research Institute of Tube Industry - RosNITI (Chelyabinsk, Russia):

D. Yu. Zvonarev, Cand. Eng., Senior Researcher, e-mail:
A. V. Vydrin, Dr. Eng., Prof., Deputy General Director on Scientific Work, e-mail:


Taganrog Metallurgical Plant – Tagmet (Taganrog, Russia)
V. L. Neroznikov, Head of tube Laboratory

ArticleName Seamless stainless tubes in coils for LNG equipment
ArticleAuthors An. V. Serebryakov, V. V. Maltsev, I. N. Bazhukov, Al. V. Serebryakov, S. I. Parshakov

Pervouralsk New Tube (Novotrubny) Works (Pervouralsk, Russia):

An. V. Serebryakov, Cand. Eng., Head of the group of new types of tubes for nuclear power industry, e-mail:
V. V. Maltsev, Head of KhDT production complex
I. N. Bazhukov, Leading engineer-researcher, the group of new types of tubes for nuclear power industry


Ural Federal University (Ekaterinburg, Russia):
Al. V. Serebryakov, Cand. Eng., Associate Prof.
S. I. Parshakov, Cand. Eng., Associate Prof.


Tsindrakova T. V., Kalabin S. V., Komelskikh S. G. (JSC Pervouralsk New Tube (Novotrubny) Works) took part in the work.

ArticleName Failure analysis of equipment of the pipe anti-corrosion coating workshop of JSC Vyksa Sreel Works
ArticleAuthors I. Yu. Murysev, V. N. Nikitaev, N. A. Chichenev

Vyksa steel works (Vyksa, Russia):

I. Yu. Murysev, Head of Repair and Maintenance Direction, e-mail:


National University of Science and Technology “MISiS”, Vyksa affiliate (Vyksa, Russia):
V. N. Nikitaev, Mag. Sci., e-mail:


National University of Science and Technology “MISiS” (Moscow, Russia):
N. A. Chichenev, Dr. Eng., Prof., e-mail:

ArticleName Features of metal stresses-strained state in hot extrusion of steel pipes
ArticleAuthors A. V. Vydrin, A. S. Zhukov, E. V. Khramkov, M. A. Pavlova

All-Russian Scientific and Research Institute of Tube Industry — RosNITI (Chelyabinsk, Russia):

A. V. Vydrin, Dr. Eng., Prof., Deputy General Director on Scientific Work, e-mail:
E. V. Khramkov, Cand. Eng., Head of the labor for simulation of technological processes
M. A. Pavlova, Senior engineer, the labor for simulation of technological processes


Volzhsky Pipe Plant (Volzhsky, Russia):

A. S. Zhukov, Director on Product Quality

ArticleName Experimental study of the change in ovality of large-diameter pipes taking into account the welding deformations effect
ArticleAuthors M. A. Tovmasyan, S. V. Samusev

National University of Science and Technology “MISiS” (Moscow, Russia):

M. A. Tovmasyan, Post-Graduate, e-mail:
S. V. Samusev, Dr. Eng., Prof.

ArticleName Thickness deviation of hot forged elliptic steel bottoms
ArticleAuthors Yu. D. Gorbunova, G. A. Orlov

Ural Federal University (Ekaterinburg, Russia):

Yu. D. Gorbunova, Engineer, Post-Graduate
G. A. Orlov, Dr. Eng., Prof., e-mail:

Heating and heat treatment
ArticleName Using a Phoenix TM autonomous automated system for monitoring temperature field of metal to be heated in metallurgical furnaces
ArticleAuthors A. A. Ulanovskiy, M. Taake, A. M. Belenkiy, A. N. Bursin, S. I. Chibizova

Obninsk Thermoelectrical company (Obninsk, Russia):

A. A. Ulanovskiy, Cand. Eng., Director


Phoenix TM GmbH (Bad Oeynrhausen, Germany):
M. Taake, Director


“Innovationa and power saving” company (Moscow, Russia):
A. M. Belenkiy, Dr. Eng., General Director
A. N. Bursin, Engineer, Senior Researcher


National University of Science and Technology “MISiS” (Moscow, Russia):
S. I. Chibizova, Cand. Eng., Associate Prof., Dept. “Power-efficient and resource-saving industrial technologies”, e-mail:

ArticleName Heat treatment of rolled steel strip in a fully automated annealing line in bell furnaces
ArticleAuthors P. Wendt, M. Flieβ, H. Muhlniclel, Ch. Hagenkord, H. Witke, D. Winkens

LOI Thermprocess GmbH (Essen, Germany):

P. Wendt, Dr., e-mail:
M. Flieβ


Bilstein Service GmbH (Hagen, Germany):
H. Mühlniclel, Mag. Eng.
Ch. Hagenkord


Kranbau Kötchen GmbH (Kötchen, Germany):
H. Witke, Cand. Eng., Director

Ludwig Bönnhof GmbH (Wetter, Germany):
D. Winkens

ArticleName An alternative to the heat treatment of cemented steels at Deutsche Edelstahlwerke
ArticleAuthors M. Schwarz, D. Kipp

Deutsche Edelstahlwerke Specialty Steel GmbH & Co. KG (Witten, Germany):

M. Schwarz, Technical consulting, high quality structural steels, e-mail:
D. Kipp, Technical marketing

Economics and finances
ArticleName The global market for metallurgical equipment: main trends
ArticleAuthor Yu. L. Adno

Institute of World Economy and International Relations (Moscow, Russia):

Adno Yu. L., Cand. Eng., Leading Researcher, e-mail:

Metallurgical history
ArticleName Features of the design and manufacture of armor protection of German tanks during the Great Patriotic War
ArticleAuthors N. N. Melnikov, B. A. Gizhevskiy, Vas. V. Zapariy, V. V. Zapariy

Institute of History and Archeology, Ural branch of the Russian Academy of Sciences (Ekaterinburg, Russia):

N. N. Melnikov, Cand Hist., Associate Prof.
Vas. V. Zapariy, Cand Hist., Associate Prof.


Institute of metal Physics, Ural branch of the Russian Academy of Sciences (Ekaterinburg, Russia):
B. A. Gizhevskiy, Cand Phys.-Math.


Ural Federal University (Ekaterinburg, Russia):
V. V. Zapariy, Dr. Hist., Prof., Dept. of Gistory and Social relations, e-mail:

Journals →  Chernye Metally →  2019 →  #9