Journals →  CIS Iron and Steel Review →  2023 →  #1 →  Back

Metal Forming and Tubemaking
ArticleName Comparative evaluation of the kinematic parameters at symmetric and asymmetric cold rolling of strip using computer simulation
DOI 10.17580/cisisr.2023.01.09
ArticleAuthor A. V. Kozhevnikov, M. M. Skripalenko, I. A. Kozhevnikova, M. N. Skripalenko
ArticleAuthorData

Cherepovets State University (Cherepovets, Russia):

A. V. Kozhevnikov, Dr. Eng., Associate Prof., Head of the Dept. of Power Engineering and Electrical Engineering, e-mail: avkozhevnikov@chsu.ru

I. A. Kozhevnikova, Dr. Eng., Associate Prof., Head of the Dept. of Metallurgy, Mechanical Engineering and Technological Equipment, e-mail: iakozhevnikova@chsu.ru

 

National University of Science and Technology “MISIS” (Moscow, Russia):

M. M. Skripalenko, Cand. Eng., Associate Prof., Dept. of Metal Forming, e-mail: mms@misis.ru
M. N. Skripalenko, Cand. Eng., Associate Prof., Dept. of Metal Forming, e-mail: tfsmn@yandex.ru

Abstract

Computer simulation of symmetric and asymmetriс cold rolling of AISI-1008 steel strip in three passes was carried out. DEFORM finite element method (FEM) software was used for computer simulation. Technique allowing neutral line location determination was designed and this technique is based on the processing of FEM computer simulation results. Neutral line location during each of three passes at different working roll diameters combinations (symmetric rolling, rolling with 0.83 %, 1.67 % and 5 % working rolls diameters asymmetry) was detected using designed technique. It was established that working rolls diameters asymmetry increase till 5 % moves the middle of the neutral line towards rolling direction in 0.250 mm for the first pass, 0.199 mm – for the second pass, 0.133 mm - for the third pass. That is, influence of working rolls diameters asymmetry increase becomes weaker with the decrease of absolute value of height reduction. Three-dimensional graphs were made: one is illustrating dependence of position of the neutral line’s midpoint from rolling speed and working rolls diameters asymmetry and the other one is illustrating dependence of the neutral line inclination angle from rolling speed and working rolls diameters asymmetry. Weak direct correlation between working rolls diameters asymmetry and position of neutral line’s middle point and strong direct correlation between rolling speed and position of neutral line’s middle point were detected. Velocity diagrams along vertical lines in lag zone and lead zone of the deformation zone at asymmetric rolling show that velocity at point of contact of upper roll and strip is less than velocity at point of contact of lower roll and strip.

The study was supported by a grant from the Russian Science Foundation, project no. 23-29-00428, https://rscf.ru/project/23-29-00428/.

keywords Cold rolling, asymmetric rolling, symmetric rolling, computer simulation, neutral line, velocity diagram, rolling speed, working rolls diameters asymmetry
References

1. Kozhevnikov A. V., Skripalenko M. M., Kozhevnikova I. A., Skripalenko M. N., Sidorov A. A., Semenov A. A., Romantsev B. A., Yusupov V. S. Estimation of Deformation Region Parameters while Symmetrycal and Asymmetrical Cold Rolling of Strip Using Computer Simulation. Tekhnologiya metallov. 2022. No. 12, pp. 43-51.
2. Khallyev R. I., Denishchenko P. N. Finite element method computer simulation of asymmetric rolling using ABAQUS software. Proceeding of the IV International Scientific and Practical Conference of Young Scientists “Metallurgy of the XXI century with the Eyes of Young”. pp. 184-186.
3. Hirohata T., Maasaki S., Shima S. Experiment on metal powder compaction by differential speed rolling. Journal of Materials Processing Technology. 2001. Vol. 111. Iss. 1-3. pp. 113–117.
4. Daming Wang, Changan Yu, Mingzhe Li, Xianzhong He, Zhijun Xie, Luo Wang Research on flexible asymmetric rolling process for three-dimensional surface parts. The International Journal of Advanced Manufacturing Technology. 2018 Vol. 95. pp. 2339–2347.
5. Lapovok R., Orlov D., Timokhina I. B., Pougis A., Toth L. S., Hodgson P. D., Haldar A., Bhattacharjee D. Asymmetric Rolling of Interstitial-Free Steel Using One Idle Roll. Metallurgical and Materials Transactions A. 2012. Vol. 43A. No. 4. pp. 1328-1340.
6. Jiang Z., Zhao J., Xie H. Simulation of Micro Ultrathin Strip Rolling. Microforming Technology. 2017. pp. 187–214.
7. Maksimov E. A., Shatalov R. L. Asymmetric deformation of metal and front flexure of thick sheet in rolling. Part 1. Steel in Translation. 2012. Vol. 42 (5). pp. 442-446.
8. Maksimov E. A., Shatalov R. L. Asymmetric deformation of metal and front flexure of thick sheet in rolling. Part 2. Steel in Translation. 2012. Vol. 42 (6). pp. 521-525.
9. Rudskoi A. I., Kodzhaspirov G. E., Kamelin E. I. Modeling of the Recrystallization Processes during Asymmetric Rolling of a High-Strength Low-Alloy Steel. Russian Metallurgy (Metally). 2021. No. 4. pp. 486–491.
10. Nilsson A. Front-end bending in plate rolling. Scandinavian Journal of Metallurgy. 2001. Vol. 30. p.337–344.
11. Akbari Mousavi S. A. A., Ebrahimi S. M., Madoliat R. Three dimensional numerical analyses of asymmetric rolling. Journal of Materials Processing Technology. 2007. No. 187–188. pp.725–729.
12. Xianwei Ren, Yuanchun Huang, Xieyi Zhang, Hao Li, Yongxing Zhao. Influence of shear deformation during asymmetric rolling on the microstructure, texture, and mechanical properties of the AZ31B magnesium alloy sheet. Materials Science and Engineering: A. 2021. Vol. 800. 140306. DOI: 10.1016/j.msea.2020.140306
13. Xu X., Deng Y., Guo X. et al. Influence of Asymmetric Rolling Process and Thickness Reduction on the Microstructure and Mechanical Properties of the Al–Mg-Si Alloy. Metals and Materials International. 2022. Vol. 28. pp. 1620-1629.
14. Pustovoytov D., Pesin A., Tandon P. Asymmetric (Hot, Warm, Cold, Cryo) Rolling of Light Alloys: A Review. Metals. 2021. Vol. 11 (6). 956.
15. Shatalov R., Kalmykov A., Taupek I. Study of the Deformation during Turning of Brass Sheets on a Two-High Mill by Rolling Methods and Computer Simulation. Russian Metallurgy (Metally). 2021. Vol. 13. pp.1771-1776.
16. Liu Y., Liu H., Liu Y. Application of Simulation in Optimization Design of Casting Billet. Proceedings of 2020 IEEE 4th Information Technology, Networking, Electronic and Automation Control Conference, ITNEC 2020. Article number 9085161. pp 1773 – 1776.
17. Sidelnikov S., Dovzhenko I., Belokonova I. Simulation of Process Rolling Plates from Alloy of Al-Mg System Economically Doped with Scandium. Solid State Phenomena. 2021. Vol. 316. pp. 509-514.
18. Wang J., Zhao Q., Wang C.. Yuan J. Effect of roll convexity and stress triaxiality on rolling damage of 93 tungsten alloy sheet. Cailiao Gongcheng/Journal of Materials Engineering. 2014. Iss. 10. pp 27 – 33.
19. Skripalenko M., Skripalenko M., Tran Ba Hui, Ashuhmin D., Samusev S., Sidorov A. Detection of influence of upper working rolls vibration on thickness of sheet at cold rolling with the help of DEFORM-3D software. Computer Research and Modeling. 2017. Vol. 9 (1). pp.111-116.
20. Skripalenko M., Skripalenko M., Ashikhmin D., Sidorov A., Yang X. Wavelet Analysis of Fluctuations in the Thickness of Cold-Rolled Strip. Metallurgist. 2013. Vol. 57 (7-8). pp. 606-611.
21. Kozhevnikov A., Bolobanova N., Kozhevnikova I., Shalaevskii D. The Study of influence of work rolls vibration during cold rolling on the quality of steel strip surface. Metalurgija (Metallurgy). 2020. Vol. 59. No. 1. pp. 74-76.
22. TESIS engineering company. DEFORM. Available at: https://tesis.com.ru/cae_brands/deform/ (Accessed: January 9, 2023).
23. Kozhevnikova I. A., Bolobanova N. L., Kozhevnikov A. V., Yusupov V. S., Kroitor E. N. Frictional-Stress Distribution in the Deformation Zone on Cold Rolling. Steel in Translation. 2018. Vol. 48. Iss. 7. pp. 454-457.
24. Baranov G. L. Influence of Strain Hardening on the Force in Cold Strip Rolling. Steel in Translation. 2018. Vol. 48. Iss. 11. pp 739-744.
25. Baranov G. L. Improved Calculation of the Contact Stress in Strip Rolling. Steel in Translation. 2015. Vol. 45. Iss. 6. pp 447-452.
26. Garber E. A., Shalaevskii D. L., Kozhevnikova I. A., Traino A. I. Simulation of the State of Stress in a Strip in a Deformation Zone with Two Neutral Sections During Cold Rolling. Russian Metallurgy (Metally). 2007. Iss. 4. pp. 293-303.
27. Garber E. A., Shalaevskii D. L., Kozhevnikova I. A., Traino A. I. Procedure and Algorithms for the Energy-Force Calculation of Cold Rolling Allowing for the Number of Neutral Sections in the Deformation Zone. Russian Metallurgy (Metally). 2008. Iss. 4. pp. 315-325.
28. Brusa E., Lemma L. Numerical and experimental analysis of the dynamic effects in compact cluster mills for Cold Rolling. Journal of Materials Processing Technology. 2009. Vol. 209 (5). pp. 2436–2445.
29. Barkov L. A., Samodurova M. N., Trofimov E. A. Computer simulation of porous material plastic deformation. Procedia Engineering. 2017. Vol. 206. pp. 533–539. Available at: DOI: 10.1016/j.proeng.2017.10.512
30. Garber E. A. Cold rolling mills (theory, equipment, technology), JSC "Chermetinformatsiya". Moscow. 2004. 416 p.
31. Hwang Y.-M., Tzou, G.-Y. Analytical and experimental study on asymmetrical sheet rolling. International Journal of Mechanical Sciences. 1997. Vol. 39 (3). pp. 289–303.

Full content Comparative evaluation of the kinematic parameters at symmetric and asymmetric cold rolling of strip using computer simulation
Back