Название |
Influence of the speed asymmetry coefficient on the power parameters and bending of a strip |
Информация об авторе |
Czestochowa University of Technology (Czestochowa, Poland):
A. A. Kawalek, Dr. Eng., Prof., Faculty of Production Technology and Materials Science H. I. Dyia, Dr. Eng., Prof., Faculty of Production Technology and Materials Science
Lipetsk State Technical University (Lipetsk, Russia): K. V. Bakhaev, Cand. Eng., Associate Prof., Metal Forming Dept. K. S. Gorbunov, Post-graduate Student, Metal Forming Dept., e-mail: beluivolk96@mail.ru |
Реферат |
The paper presents the results of modeling the influence of the asymmetric rolling process on the change in energy-power parameters of the rolling process and the bending of the strip after the deformation zone at various reductions ε = 0.03 ÷ 0.15. Simulation of the asymmetric rolling process was carried out using the FEM based Forge 2008® program. Asymmetry was carried out by changing the circumferential speed of work rolls when rolling samples with a thickness of 120 and 12 mm from low-alloy steel with increased strength S355J2 + N (+N - as delivered after normalizing rolling). The aim of the research was to determine the asymmetry coefficient to reduce the energypower parameters of the rolling process (the average linear load per 1 mm of the strip width and rolling power), the direction and magnitude of the strip bending after leaving the deformation zone. On the basis of the studies carried out, it was found that the ratio h0/D significantly affects the decrease in the strip linear load through the rolls and strip bending, and it is possible to obtain a given curvature of the strip that does not impede the free exit from the stand. |
Библиографический список |
1. Aboutorabi A., Assempour A., Afrasiab H. Analytical approach for calculating the sheet output curvature in asymmetrical rolling: In the case of roll axis displacement as a new asymmetry factor. International Journal of Mechanical Sciences. 2016. Vol. 105. pp. 11–22. 2. Dyja H., Markowski J., Kawalek A. Effect of asymmetrical rolling on broadening of the product line of rolled sheets. 2003. Vol. 42. No. 3. pp. 207–211. 3. Kawalek A. Forming of band curvature in asymmetrical rolling process. Journal of materials processing technology. 2004. Vol. 150. pp. 2033–2038. 4. Borkowski S., Szyiński P., Szklarzyk P. Analiza wpływu współczynnika tarcia na zamianę nacisku podczas asymetrycznego walcowania blach grubych na gorąco. Wiadomości Hutnicze. 2011. No. 9. pp. 3–6. 5. Farhatnia F., Salimi M., Movahhedy M. R. Elastoplastic finite element simulation of asymmetrical plate rolling using an ALE approach. Journal of Materials Processing Technology. 2006. Vol. 177. pp. 525–529. 6. Farhatnia F., Salimi M. Effect of entry bending moment on exit curvature in asymmetrical rolling. International Journal of Engineering, Science and Technology. 2011. Vol. 3. No. 4. pp. 147–163. 7. Gudur P. P., Salunkhe M. A., Dixit U. S. A theoretical study on the application of asymmetric rolling for the estimation of friction. International Journal of Mechanical Science. 2008. Vol. 50. pp. 315–327. 8. Dyja H., Wilk K. Asymetryczne walcowanie blach i taśm. Seria: Metalurgia. — Częstochowa: Wydawnictwo Wydziału Metalurgii i Inżynierii Materiałowej Politechniki Częstochowskiej, 1998. 268 p. 9. Kawalek A., Dyja H., Ozhmegov K. V. Variations of the rheological properties of steel in the plate rolling process conditions. CIS Iron and Steel Review. 2020. Vol. 19. pp. 37–43. 10. Markowski J., Dyja H., Knapinski M., Kawalek A. Theoretical analysis of the asymmetric rolling of sheets on leader and finishing stands. Journal of materials processing technology. 2003. Vol. 138, Iss. 1–3. pp. 183–188. 11. Gorbunov К. S., Bakhaev К. V. Asymmetric rolling. Improvement of the efficiency of metallurgical production. Collection of materials of the XXVII regional scientific and technical conference. 2019. pp. 140–143. 12. Gorbunov К. S., Bakhaev К. V. Asymmetric rolling process. Metallurgy of the XXI century through the eyes of young people: proceedings of the V International scientific and practical conference of young scientists and students. 2019. pp. 193–196. 13. Gorbunov К. S. Advantages of asymmetric rolling. Materials of the regional specialized seminar. Lipetsk, 2020. pp. 47–49. |